» über uns

» Registrierung

Liebe Mitleserinnen, Mitleser, Foristinnen und Foristen,

wer sich von Euch in letzter Zeit mit dem Gedanken getragen hat, Mitglied unseres wunderbaren IGDH-Forums zu werden und die vorher an dieser Stelle beschriebene Prozedur dafür auf sich genommen hat, musste oftmals enttäuscht feststellen, dass von unserer Seite keine angemessene Reaktion erfolgte.

Dafür entschuldige ich mich im Namen des Vereins!

Es gibt massive technische Probleme mit der veralteten und mittlerweile sehr wackeligen Foren-Software und die Freischaltung neuer User ist deshalb momentan nicht mit angemessenem administrativem Aufwand möglich.

Wir arbeiten mit Hochdruck daran, das Forum neu aufzusetzen und es sieht alles sehr vielversprechend aus.

Sobald es dies bezüglich Neuigkeiten, respektive einen Zeitplan gibt, lasse ich es Euch hier wissen.

Das wird auch für alle hier schon registrierten User wichtig sein, weil wir dann mit Euch den Umzug auf das neue Forum abstimmen werden.

Wir freuen uns sehr, wenn sich die geneigten Mitleserinnen und Mitleser, die sich bisher vergeblich um eine Freischaltung bemüht haben, nach der Neuaufsetzung abermals ein Herz fassen wollen und wir sie dann im neuen Forum willkommen heißen können.

Herzliche Grüße von Eurem ersten Vorsitzenden der IGDH

Rainer Feile
Seite 1 von 2 1 2 LetzteLetzte
Zeige Ergebnis 1 bis 20 von 32
  1. #1
    Getting out of the Matrix Benutzerbild von Zvu
    Registriert seit
    30.12.2017
    Ort
    Serbia - Belgrade
    Beiträge
    26

    Standard Kef R300 playground - measurements of raw drivers

    I did some measurements of Kef R300 raw drivers. Rain prevented making full set of measurements but i found quiet enough neighbourhood so yesterday at about 01:00am some sweeps were heard from the parking lot.



    https://s15.postimg.cc/5exyq4gu1/image.png



    https://s15.postimg.cc/ivux8zyvd/image.png



    https://s15.postimg.cc/8lsi9rgpl/image.png


    This amount of quasi anechoic resolution makes it much easier to simulate the crossover between woofer and midrange.



    https://s15.postimg.cc/y5cvgw7l5/image.png


    I've managed to get about 9ms of gate time. I'm quite satisfied with consistency so here are files for simulators.


    https://www.dropbox.com/s/dzg8gzfclg...files.zip?dl=0


    Few words about it.


    You'll find on axis and about 45deg off axis files in .zip folder. Only woofers are merged (between 100-200Hz). Mids and tweeters aren't because there's no need to. You have everything you need to derive Z axis offset. You'll find that frequency response of midrange+tweeter, that is needed to derive Z offset between them, drops bellow 300Hz. I am protecting the tweeter that way so, when deriving Z offset, look only how combined frequency response behaves over 300Hz in regard to reference. As far as X and Y offsets all you need to know is that woofer and midrange centers are 26cm apart. There are impedance files there. Just in case you don't like how i extracted my sim files i added HolmImpulse measurements .zip file that you can import into your HolmImpulse and set the gate to derive files as you see fit.


    Here's Kef's crossover. I betcha you can do better than that if you try:



    https://s15.postimg.cc/43flgo7hn/300.png


    Measurements are done in factory cabinets, gated, at 1.03 m distance mic at tweeter axis - gate is good to 100Hz. Holm-impulse, calibrated ECM8000, M-Audio Fast Track II USB interface, Dell Inspiron notebook.


    Play and enjoy yourself (:
    Geändert von Zvu (13.07.2018 um 15:08 Uhr)

  2. #2
    Erfahrener Benutzer
    Registriert seit
    10.01.2018
    Beiträge
    433

    Standard

    Excellent work, thank you very much for providing it freely!

  3. #3
    Getting out of the Matrix Benutzerbild von Zvu
    Registriert seit
    30.12.2017
    Ort
    Serbia - Belgrade
    Beiträge
    26

    Standard

    Bitte

    It's all about the compromise on axis vs off axis. Here's my quick and dirty take on it.

    Klicke auf die Grafik für eine größere Ansicht

Name:	Webp.net-gifmaker.gif
Hits:	181
Größe:	111,7 KB
ID:	44237Klicke auf die Grafik für eine größere Ansicht

Name:	Скретница.png
Hits:	266
Größe:	17,5 KB
ID:	44238

    Phase tracking is quite good but keeping the impedance above 3 ohms while maintaining linear frequency response and good phase tracking will be quite challenging.

  4. #4
    wohnt neben dem Mühlstein Benutzerbild von bee
    Registriert seit
    19.11.2008
    Ort
    Taunus
    Beiträge
    787

    Standard

    I agree, much better way to sweep the parking lot than those bloody americans with their rental Mustangs....

    In case the woofer is too loud, last resort might be to stuff the port and increase Rdc of the inductors in the low-pass until it works o.k. in that CB. May work if the woofer-TSP are so-so.
    Yes, I know, nasty....
    Viele Grüße

    Bernd

  5. #5
    Getting out of the Matrix Benutzerbild von Zvu
    Registriert seit
    30.12.2017
    Ort
    Serbia - Belgrade
    Beiträge
    26

    Standard

    You're right on the money there. Factory coil on woofer is 2.2mH but Rdc is quite high. It is ferrite coil so maybe it is smart to change it, regardless if that Rdc suits us. I'm trying to make the crossover with as much components reused -to make it simple and less expensive- but series coil on woofer and midrange definitely should be of higher quality as should series capacitors. Those 10mH are unwinded from factory 22mH that was on woofer notch centered at 90Hz. I've kept that noch to linearize the bass but changed the values to obtain better result, in my opinion. We'll see where this ends. It'll be a journey.
    Geändert von Zvu (13.07.2018 um 21:17 Uhr)

  6. #6
    Getting out of the Matrix Benutzerbild von Zvu
    Registriert seit
    30.12.2017
    Ort
    Serbia - Belgrade
    Beiträge
    26

    Standard

    I forgot to upload pics of impedance and woofer TS.

    Woofer impedance in cabinet:



    Midrange impedance in cabinet:



    Tweeter impedance:



    TS parameters for woofer:
    Geändert von Zvu (14.07.2018 um 17:36 Uhr)

  7. #7
    Gast
    Registriert seit
    18.02.2014
    Ort
    Bayern
    Beiträge
    2.562

    Standard

    Thanks for sharing

  8. #8
    Erfahrener Benutzer
    Registriert seit
    01.03.2010
    Ort
    Birkenau
    Beiträge
    417

    Blinzeln

    yesterday at about 01:00am some sweeps were heard from the parking lot
    You made my day
    regards Jens

  9. #9
    Getting out of the Matrix Benutzerbild von Zvu
    Registriert seit
    30.12.2017
    Ort
    Serbia - Belgrade
    Beiträge
    26

    Standard

    @Jens

    Ich freue mich


    @Bee

    Hier ist das original schaltbild für den tieftöner frequenzweiche:

    Klicke auf die Grafik für eine größere Ansicht

Name:	Фабричка скрет&#10.png
Hits:	183
Größe:	61,5 KB
ID:	44249
    Geändert von Zvu (14.07.2018 um 21:11 Uhr)

  10. #10
    Getting out of the Matrix Benutzerbild von Zvu
    Registriert seit
    30.12.2017
    Ort
    Serbia - Belgrade
    Beiträge
    26

    Standard

    I've been listening these speakers past two weeks and tweaking a bit. Nothing dramatically changed but few details for better phase matching and a bit more linearity. I'm at the stage of putting the crossovers into the cabinets so here's few screenshots:


    Midrange in phase:


    https://s15.postimg.cc/6xh5avkyj/Web...gifmaker_1.gif




    Midrange out of phase:


    https://s15.postimg.cc/mvpv10mwb/Webp.net-gifmaker.gif




    Simplistic crossover:


    https://s15.postimg.cc/jovbh6s3v/image.png




    "Exploded" view:


    https://s15.postimg.cc/xvb2cfxu3/image.png


    I didn't measure both loudspeaker cabinets but i have just now checked for production consistency with indoor measurements. There is slight difference between the midrange drivers frequency response.



    https://s15.postimg.cc/rake0dlqj/srednjetonci.png


    Both loudspeakers now measure the same but it's always a good thing to check. In an interview, with John Atkinson, Jack Oclee-Brown explains - voice coil of their drivers isn't rigidly coupled with the cone. They are interconnected with a damping ring that is incompressible at lower frequencies but acts as a "shock absorber" for frequencies above 5KHz to minimize the breakup. I had my suspicions about damping system of that sort because that fine details are dependent on compressibility of that ring and on amount of glue applied. This lead to a slightly different crossover for midrange - on one loudspeaker series midrange coil is 1mH and on the other it is 0.9mH.

    Anyhow, here's how the crossover will look like - few resistors missing but soon to be acquired and all electrolytic caps are going to be bypassed with 0.1uF mkc.



    https://s15.postimg.cc/4ny2wzpzf/DSC_0070.jpg

    viele grüße
    Geändert von Zvu (18.09.2018 um 14:56 Uhr)

  11. #11
    Erfahrener Benutzer
    Registriert seit
    10.01.2018
    Beiträge
    433

    Standard

    Thanks for the update, so you have chosen now a tilted on axis frequency response? This is interesting as also this years forum contest winner with a KEF coaxial project (KEFIR https://www.diy-hifi-forum.eu/forum/...-Projekt-KEFIR ) as well as KEF themselves in their newest models seem also to have chosen a slightly tilted 0° response http://international.kef.com/media/d...tepaper_en.pdf .

  12. #12
    Getting out of the Matrix Benutzerbild von Zvu
    Registriert seit
    30.12.2017
    Ort
    Serbia - Belgrade
    Beiträge
    26

    Standard

    Yogi did helluva job there. I really like the name and the looks of this years winner - It's obvious that it had to be white

    Slightly tilted response, yes. Since there are diffraction products on axis (no shadow flare on 2011 R series version - which would be the one thing i'm jealous about what new R series have) i had to observe frequency response off-axis and 6dB smoothing on axis. That way i can see distribution of energy across the spectrum. It looks like this - thank god for VituixCAD and LspCAD:

    Klicke auf die Grafik für eine größere Ansicht

Name:	Untitled1.png
Hits:	135
Größe:	24,7 KB
ID:	45431 Klicke auf die Grafik für eine größere Ansicht

Name:	Untitled2.png
Hits:	121
Größe:	12,7 KB
ID:	45432

    I listen them with slight toe in - so their 0° axis cross in front of my head more or less. It flattens tweeter response and although it is very good tweeter, that diffraction on axis is perceivable so i had to make it quieter about dB or so. In larger rooms i guess you could get by without tweeter resistor.

    The crossover topology in new R series is quite similar to Reference series. If you play with values a bit, you get individual responses quite similar to Kef Ref 1 measured here:

    https://www.fidelity-magazin.de/2016...e-1-messungen/

    Although R300 measured good with that topology, it didn't do it for me soundwise. I think it is because of midrange resonance (around 200Hz) being to high in level - but i cannot be certain. What i do know is that i like my crossover better even though it hits 2.6 ohm impedance at 250Hz.
    Geändert von Zvu (18.09.2018 um 22:53 Uhr)

  13. #13
    Erfahrener Benutzer
    Registriert seit
    10.01.2018
    Beiträge
    433

    Standard

    Thank you again very much for your thorough and very interesting response!

  14. #14
    Getting out of the Matrix Benutzerbild von Zvu
    Registriert seit
    30.12.2017
    Ort
    Serbia - Belgrade
    Beiträge
    26

    Standard

    I've made some more measurements last night to see the agreement of simulator to measured response. There is a slight upward tilt toward high frequencies but that could be due to cold (6 degrees Celsius last night). By the looks of it, if it is real, the tweeter is about 1.5-2dB hotter but final level is to be determined indoors by listening. So, without further ado...


    On axis:

    Klicke auf die Grafik für eine größere Ansicht

Name:	Напољу на оси.png
Hits:	138
Größe:	48,3 KB
ID:	45966

    Off axis 10 and 20 degrees

    Klicke auf die Grafik für eine größere Ansicht

Name:	на и ван осе до 20 с&#10.png
Hits:	121
Größe:	54,1 KB
ID:	45965

    Up to 45 degrees

    Klicke auf die Grafik für eine größere Ansicht

Name:	на и ван осе до 45 с&#10.png
Hits:	109
Größe:	55,2 KB
ID:	45964




    The crossover work is pretty much done so for the winter i'll be doing nothing but listening music and maybe a little tweaking by ear. This was very enjoyable experience


    viele grüße

  15. #15
    Getting out of the Matrix Benutzerbild von Zvu
    Registriert seit
    30.12.2017
    Ort
    Serbia - Belgrade
    Beiträge
    26

    Standard

    es lebt

    0, 10, 20, 30, 60 und 90 grad


    Klicke auf die Grafik für eine größere Ansicht

Name:	КЕФ Р300.gif
Hits:	130
Größe:	225,8 KB
ID:	46120
    Geändert von Zvu (02.11.2018 um 18:56 Uhr)

  16. #16
    Erfahrener Benutzer
    Registriert seit
    05.03.2016
    Ort
    Güstrow
    Beiträge
    1.461

    Standard

    Eine sehr lebhafte Abstimmung! ( : quite a lively voicing).

  17. #17
    Getting out of the Matrix Benutzerbild von Zvu
    Registriert seit
    30.12.2017
    Ort
    Serbia - Belgrade
    Beiträge
    26

    Standard



    Es braucht jedoch etwas mehr feinabstimmung. Ich mag es nicht wie es im bereich von 7-12 KHz aussieht.

    Sorry for my lousy German. I'm still learning - from GT Feel free to send me to the bench when i mess up badly

    Viele Grüße

  18. #18
    Erfahrener Benutzer
    Registriert seit
    05.03.2016
    Ort
    Güstrow
    Beiträge
    1.461

    Standard

    Kann ich verstehen. Wenn ich nach den Bildern in Post #14 gehe, wäre mir das in dem von dir genannten Bereich auch zuviel. Vermute ich.

    VG, Matthias

  19. #19
    Getting out of the Matrix Benutzerbild von Zvu
    Registriert seit
    30.12.2017
    Ort
    Serbia - Belgrade
    Beiträge
    26

    Standard

    Es ist jetzt ziemlich kalt draußen (6 grad Celsius). Das wetter wird sich für das wochenende verbessern (20 grad Celsius) also erwarte ich es wieder mit verbesserter frequenzweiche zu messen.

    Viele Grüße
    Geändert von Zvu (25.10.2018 um 21:30 Uhr)

  20. #20
    Erfahrener Benutzer Benutzerbild von chro
    Registriert seit
    01.02.2014
    Ort
    Schwarzwald
    Beiträge
    335

    Standard

    Servus,

    schau mal ich verwende den Mittel/Hochton Zweig mit der grünen Hochton Abstimmung. Bin sehr zufrieden damit

    http://www.audioexcite.com/?page_id=3807


    Zum Tieftöner fahre ich aktiv. Und zu deinem deutsch. Das ist wahrscheinlich besser als mein englisch

    Klicke auf die Grafik für eine größere Ansicht

Name:	IMG_7971.JPG
Hits:	233
Größe:	259,9 KB
ID:	46026
    Argument: Du kannst Religion nicht kritisieren, weil du kein Theologie Experte bist. Doch, ich kann Feen ablehnen ohne Feen-ologe zu sein

Forumregeln

  • Es ist dir nicht erlaubt, neue Themen zu verfassen.
  • Es ist dir nicht erlaubt, auf Beiträge zu antworten.
  • Es ist dir nicht erlaubt, Anhänge hochzuladen.
  • Es ist dir nicht erlaubt, deine Beiträge zu bearbeiten.
  •  
Powered by vBadvanced CMPS v4.3.0